n0-0ne
15th September 2006, 08:27 PM
I am trying to make my ipw2100 card to work with wpa on fc4
I have upgraded the kernel to 2.6.17-1.2142_FC4
and downloaded wirless tools v28
I saw wirless tools supports WPA but it doesn't seem to do anything to connect.
when I use network configure to activate the dev it works fine but only when WPA is desabled in my router
I'm not sure if I need wpa_supplicant but after not being able to connect when wpa is enabled I've
installed v0.4.9
when I run it i get a bunch of data which runs in loop, from what I could figure out the only disterbing msg
is "ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported"
I saw somewhere on the net its not suppose to cose any proble
when I run wpa_cli
I get the following lines over and over again
<2>Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
<2>Authentication with 00:00:00:00:00:00 timed out.
if I ask for scan , and scan results it seems to be getting the right info
bssid / frequency / signal level / flags / ssid
00:0e:2e:5f:eb:58 0 0 [WPA-PSK-TKIP] Yhome
so I'm kind of lost in figuring out what the problem google wasn't much help either.
my conf file contain the following lines -
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="Yhome"
scan_ssid=1
key_mgmt=WPA-PSK
psk="my password"
pairwise=TKIP
group=TKIP
proto=WPA
}
and the full output of wpa_supplicant debug is
wpa_supplicant -ieth1 -c/etc/wpa_sup.conf -D ipw -d
Initializing interface 'eth1' conf '/etc/wpa_sup.conf' driver 'ipw' ctrl_interface 'N/A'
Configuration file '/etc/wpa_sup.conf' -> '/etc/wpa_sup.conf'
Reading configuration file '/etc/wpa_sup.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='Yhome'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
Own MAC address: 00:04:23:8e:0b:6c
wpa_driver_ipw_set_wpa: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_countermeasures: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting scan request: 0 sec 100000 usec
Added interface eth1
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=5):
59 68 6f 6d 65 Yhome
Scan timeout - try to get results
Received 471 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 0
0: 00:0e:2e:5f:eb:58 ssid='Yhome' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=14
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 471 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 0
0: 00:0e:2e:5f:eb:58 ssid='Yhome' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=14
Authentication with 00:00:00:00:00:00 timed out.
BSSID 00:00:00:00:00:00 blacklist count incremented to 2
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=5):
59 68 6f 6d 65 Yhome
...
....
I have upgraded the kernel to 2.6.17-1.2142_FC4
and downloaded wirless tools v28
I saw wirless tools supports WPA but it doesn't seem to do anything to connect.
when I use network configure to activate the dev it works fine but only when WPA is desabled in my router
I'm not sure if I need wpa_supplicant but after not being able to connect when wpa is enabled I've
installed v0.4.9
when I run it i get a bunch of data which runs in loop, from what I could figure out the only disterbing msg
is "ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported"
I saw somewhere on the net its not suppose to cose any proble
when I run wpa_cli
I get the following lines over and over again
<2>Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
<2>Authentication with 00:00:00:00:00:00 timed out.
if I ask for scan , and scan results it seems to be getting the right info
bssid / frequency / signal level / flags / ssid
00:0e:2e:5f:eb:58 0 0 [WPA-PSK-TKIP] Yhome
so I'm kind of lost in figuring out what the problem google wasn't much help either.
my conf file contain the following lines -
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="Yhome"
scan_ssid=1
key_mgmt=WPA-PSK
psk="my password"
pairwise=TKIP
group=TKIP
proto=WPA
}
and the full output of wpa_supplicant debug is
wpa_supplicant -ieth1 -c/etc/wpa_sup.conf -D ipw -d
Initializing interface 'eth1' conf '/etc/wpa_sup.conf' driver 'ipw' ctrl_interface 'N/A'
Configuration file '/etc/wpa_sup.conf' -> '/etc/wpa_sup.conf'
Reading configuration file '/etc/wpa_sup.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='Yhome'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
Own MAC address: 00:04:23:8e:0b:6c
wpa_driver_ipw_set_wpa: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Failed to set encryption.
wpa_driver_ipw_set_countermeasures: enabled=0
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting scan request: 0 sec 100000 usec
Added interface eth1
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=5):
59 68 6f 6d 65 Yhome
Scan timeout - try to get results
Received 471 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 0
0: 00:0e:2e:5f:eb:58 ssid='Yhome' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=14
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 471 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 0
0: 00:0e:2e:5f:eb:58 ssid='Yhome' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:0e:2e:5f:eb:58 (SSID='Yhome' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_ipw_set_drop_unencrypted: enabled=1
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
State: SCANNING -> ASSOCIATING
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
ioctl[IPW_IOCTL_WPA_SUPPLICANT]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=14
Authentication with 00:00:00:00:00:00 timed out.
BSSID 00:00:00:00:00:00 blacklist count incremented to 2
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=5):
59 68 6f 6d 65 Yhome
...
....