WLAN not working on FC3 Intersil PRISM2 Toshiba Satellite Pro 4600

[k8lin]

Hello!

I have a Toshiba Satellite Pro 4600 (aka a cinder block) running Fedora Core 3. It contains an onboard wired ethernet card at eth0, which works. It also contains an onboard wireless card at eth1 which does not work. It used to work. I run yum update indiscriminately (kernel and all) and I am not sure if one of these updates broke it, or it is a hardware failure. (Or... other. )

When I initially installed FC3 on this machine, it took some doing to get wireless to work, and I ended up getting some help from someone at work who found an interrupt conflict. I am also wondering if an update reverted what he did. Unfortunately, I don't know what he did, or I would include that. I'd rather not bother him again with this mess as he is prohibitively busy.

So, below you'll find the kernel version (2.6.12-1.1376_FC3), and more. I was going to include dmesg here but it's too long so I will have to add it to this thread in the next post. The card was initially working in the Network Configuration Tool as an Intersil PRISM2.

Thanks in advance for any insight you can give into this problem.

Caitlin

[root@machine network-scripts]# /sbin/ifup eth1

Determining IP information for eth1... failed; no link present. Check cable?

[root@machine network-scripts]# uname -r
2.6.12-1.1376_FC3

[root@machine network-scripts]# /sbin/iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

eth1 IEEE 802.11b ESSID:"Singularity" Nickname:"machine"
Mode:Managed Frequency:2.412 GHz Access Point: 44:44:44:44:44:44
Bit Rate=11 Mb/s Sensitivity:1/3
Retry limit:4 RTS thr:off Fragment thr:off
Encryption key: [deleted] Security mode:open
Power Management:off
Link Quality=0/92 Signal level=134/153 Noise level=134/153
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


[root@machine network-scripts]# cat /proc/interrupts
CPU0
0: 7645957 XT-PIC timer
1: 8626 XT-PIC i8042
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
11: 92205 XT-PIC Intel 82801BA-ICH2, Intel ICH Modem, uhci_hcd:usb1, uhci_hcd:usb2, yenta, yenta, yenta, 0.0, eth0
12: 336475 XT-PIC i8042
14: 113682 XT-PIC ide0
15: 67828 XT-PIC ide1
NMI: 0
ERR: 0

[root@machine network-scripts]# /sbin/lsmod
Module Size Used by
loop 18121 0
parport_pc 28293 1
lp 12873 0
parport 40073 2 parport_pc,lp
autofs4 28229 0
i2c_dev 10945 0
i2c_core 21313 1 i2c_dev
sunrpc 164229 1
orinoco_cs 10185 1
orinoco 54741 1 orinoco_cs
hermes 7105 2 orinoco_cs,orinoco
pcmcia 28897 25 orinoco_cs
ipt_REJECT 5441 1
ipt_state 1857 4
ip_conntrack 41369 1 ipt_state
iptable_filter 2881 1
ip_tables 19521 3 ipt_REJECT,ipt_state,iptable_filter
dm_mod 57333 0
md5 4033 1
ipv6 263105 8
yenta_socket 21705 4
rsrc_nonstatic 12737 1 yenta_socket
pcmcia_core 50013 4 orinoco_cs,pcmcia,yenta_socket,rsrc_nonstatic
uhci_hcd 35025 0
hw_random 5973 0
snd_intel8x0m 19333 0
snd_intel8x0 34177 0
snd_ac97_codec 74937 2 snd_intel8x0m,snd_intel8x0
snd_pcm_oss 50673 0
snd_mixer_oss 17729 1 snd_pcm_oss
snd_pcm 98889 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_ oss
snd_timer 32837 1 snd_pcm
snd 57285 7 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_ oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10785 1 snd
snd_page_alloc 9669 3 snd_intel8x0m,snd_intel8x0,snd_pcm
e100 48705 0
mii 5569 1 e100
floppy 64629 0
ext3 130633 2
jbd 83161 1 ext3


[root@machine network-scripts]# /sbin/lspci
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 11)
00:01.0 PCI bridge: Intel Corporation 82815 815 Chipset AGP Bridge (rev 11)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (LPC) (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03)
00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 03)
00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801BA/BAM AC'97 Audio (rev 03)
00:1f.6 Modem: Intel Corporation 82801BA/BAM AC'97 Modem (rev 03)
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/XP (rev 63)
02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 03)
02:0c.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
02:0d.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 31)
02:0d.1 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 31)

[root@machine network-scripts]# /sbin/ifconfig eth1 up
[root@machine network-scripts]# /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:00:39:39:58:3A
inet addr:192.168.0.103 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::200:39ff:fe39:583a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:49075 errors:0 dropped:0 overruns:0 frame:0
TX packets:46051 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:67253565 (64.1 MiB) TX bytes:3821154 (3.6 MiB)

eth1 Link encap:Ethernet HWaddr 00:02:2D:11:BF:84
inet6 addr: fe80::202:2dff:fe11:bf84/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0x100

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2751 errors:0 dropped:0 overruns:0 frame:0
TX packets:2751 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3320797 (3.1 MiB) TX bytes:3320797 (3.1 MiB)

[k8lin]

Last bit of dmesg is in next post.

[root@machine network-scripts]# dmesg | more
Linux version 2.6.12-1.1376_FC3 (bhcompile@tweety.build.redhat.com) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 Fri Aug 26 23:27:26 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ff60000 (usable)
BIOS-e820: 000000000ff60000 - 000000000ff70000 (ACPI data)
BIOS-e820: 000000000ff70000 - 0000000010000000 (reserved)
BIOS-e820: 00000000feea0000 - 00000000feec0000 (reserved)
BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 65376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Allocating PCI resources starting at 10000000 (gap: 10000000:eeea0000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet acpi=off
Initializing CPU#0
CPU 0 irqstacks, hard=c0447000 soft=c0446000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 847.630 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254316k/261504k available (2450k kernel code, 6564k reserved, 694k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1675.26 BogoMIPS (lpj=837632)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 394k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdbab, last bus=7
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050729
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/244c] at 0000:00:1f.0
PCI: IRQ 0 for device 0000:02:0c.0 doesn't match PIRQ mask - try pci=usepirqmaskPCI: Found IRQ 11 for device 0000:02:0c.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: IRQ 0 for device 0000:02:0d.0 doesn't match PIRQ mask - try pci=usepirqmaskPCI: Found IRQ 11 for device 0000:02:0d.0
PCI: IRQ 0 for device 0000:02:0d.1 doesn't match PIRQ mask - try pci=usepirqmaskPCI: Found IRQ 11 for device 0000:02:0d.1
PCI: Sharing IRQ 11 with 0000:00:1f.5
PCI: Sharing IRQ 11 with 0000:00:1f.6
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1127421843.540:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key ACD1A80A1D789A78
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0xf0000000
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 11 for device 0000:00:1f.6
PCI: Sharing IRQ 11 with 0000:00:1f.5
PCI: Sharing IRQ 11 with 0000:02:0d.1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2M: IDE controller at PCI slot 0000:00:1f.1
ICH2M: chipset revision 3
ICH2M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xcff0-0xcff7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xcff8-0xcfff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IBM-DJSA-220, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-R2002, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1874KiB Cache, CHS=38760/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 180k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
logips2pp: Detected unknown logitech mouse model 0
input: PS/2 Logitech Mouse on isa0060/serio1
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077

... continued in next post...

[k8lin]

e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
PCI: Found IRQ 11 for device 0000:02:08.0
e100: eth0: e100_probe: addr 0xf7dff000, irq 11, MAC addr 00:00:39:39:58:3A
PCI: Found IRQ 11 for device 0000:00:1f.5
PCI: Sharing IRQ 11 with 0000:00:1f.6
PCI: Sharing IRQ 11 with 0000:02:0d.1
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49241 usecs
intel8x0: clocking to 48000
PCI: Found IRQ 11 for device 0000:00:1f.6
PCI: Sharing IRQ 11 with 0000:00:1f.5
PCI: Sharing IRQ 11 with 0000:02:0d.1
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 1 converters and GPIO not ready (0xf200)
hw_random hardware driver 1.0.0 loaded
USB Universal Host Controller Interface driver v2.2
PCI: Found IRQ 11 for device 0000:00:1f.2
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000cf80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1f.4
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: irq 11, io base 0x0000cf60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:0c.0 (0000 -> 0002)
PCI: Found IRQ 11 for device 0000:02:0c.0
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:02:0c.0 [12a3:ab01]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:0c.0, mfunc 0x01000002, devctl 0x60
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000059
PCI: Found IRQ 11 for device 0000:02:0d.0
Yenta: CardBus bridge found at 0000:02:0d.0 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
PCI: Found IRQ 11 for device 0000:02:0d.1
PCI: Sharing IRQ 11 with 0000:00:1f.5
PCI: Sharing IRQ 11 with 0000:00:1f.6
Yenta: CardBus bridge found at 0000:02:0d.1 [1179:0001]
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000007
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03d60a0(lo)
IPv6 over IPv4 tunneling driver
EXT3 FS on hda2, internal journal
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 522104k swap on /dev/hda3. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ieee1394: Initialized config rom entry `ip1394'
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (2043 buckets, 16344 max) - 272 bytes per conntrack
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
eth1: Hardware identity 0005:0002:0001:0002
eth1: Station identity 001f:0001:0006:000e
eth1: Firmware determined as Lucent/Agere 6.14
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:11:BF:84
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 11, io 0x0100-0x013f
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
i2c /dev entries driver
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth1: no IPv6 routers present
application firefox-bin uses obsolete OSS audio interface
eth1: no IPv6 routers present
eth1: New link status: Disconnected (0002)
loop: loaded (max 8 devices)
eth1: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
usb 1-1: USB disconnect, address 2
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
eth0: no IPv6 routers present
eth1: no IPv6 routers present
eth1: New link status: Disconnected (0002)
eth1: no IPv6 routers present

[k8lin]

Could anyone tell me how I can rule out hardware conflicts? I'd like to move the Wireless card to a different IRQ and try that, but I don't know how.

[k8lin]

Still no dice. I've tried some of the command listed in similar threads, but with no relief. I particularly tried this:
http://www.deepblue.uk.net/fortopic107.html

I get the error below on startup and network restart. Any advice would be appreciated.

[root@compy sbin]# service network restart
Shutting down interface eth0: [ OK ]
Shutting down loopback interface: [ OK ]
Setting network parameters: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0: [ OK ]
Bringing up interface eth1:
Determining IP information for eth1... failed; no link present. Check cable?
[FAILED]