 |
 |
 |
 |
| Fedora Core 4 Test For discussion of issues related to Fedora Core 4 Test releases. |
1st May 2005, 11:59 PM
|
 |
Registered User
|
|
Join Date: Apr 2005
Location: Western Hemisphere
Posts: 13
|
|
No sound
I am not sure what info will specifically help but after an update a few days ago I lost alsa sound on my laptop (IBM ThinkPad a22m) under FC4t2.
[madison@akane cgi-bin]$ sudo lspci -vv
Password:
...
00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
Subsystem: IBM: Unknown device 0153
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4122000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[madison@akane cgi-bin]$ sudo cat /var/log/dmesg
Linux version 2.6.11-1.1276_FC4 (bhcompile@decompose.build.redhat.com) (gcc version 4.0.0 20050423 (Red Hat 4.0.0-2)) #1 Fri Apr 29 01:35:28 EDT 2005
...
<can't find anything related to audio>
In XMMS I can switch to OSS for sound and I get music just fine. In the rest of Gnome though I hear nothing any more (ie: Gaim, etc...). Failing a fix for alsa, can anyone tell me what I need to do to make OSS the default?
I'll reply with all the output from 'lspci' and 'dmesg'. Is there anything else useful I could post?
Madison
|
2nd May 2005, 12:00 AM
|
|
Registered User
|
|
Join Date: Apr 2005
Location: Western Hemisphere
Posts: 13
|
|
Code:
[madison@akane cgi-bin]$ sudo lspci -vv
Password:
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4200000-f5ffffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-203ff000 (prefetchable)
Memory window 1: 20400000-207ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
Subsystem: IBM: Unknown device 0130
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 20800000-20bff000 (prefetchable)
Memory window 1: 20c00000-20fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:03.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0c)
Subsystem: Intel Corporation EtherExpress PRO/100 SP Mobile Combo Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4120000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1800 [size=64]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
00:03.1 Serial controller: Agere Systems (former Lucent Microelectronics) LT WinModem (rev 01) (prog-if 00 [8250])
Subsystem: Intel Corporation: Unknown device 2205
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1840 [size=8]
Region 1: Memory at f4121000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01)
Subsystem: IBM: Unknown device 0153
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4122000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1850 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
Subsystem: IBM ThinkPad A20m
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at f4200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
2nd May 2005, 12:02 AM
|
|
Registered User
|
|
Join Date: Apr 2005
Location: Western Hemisphere
Posts: 13
|
|
Code:
[madison@akane cgi-bin]$ sudo cat /var/log/dmesg
Linux version 2.6.11-1.1276_FC4 (bhcompile@decompose.build.redhat.com) (gcc version 4.0.0 20050423 (Red Hat 4.0.0-2)) #1 Fri Apr 29 01:35:28 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fffec00 (ACPI data)
BIOS-e820: 000000001fffec00 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7160
ACPI: RSDT (v001 PTLTD RSDT 0x06041040 LTP 0x00000000) @ 0x1fff57e6
ACPI: FADT (v001 IBM TP-A21m 0x06041040 0x00000000) @ 0x1fffeb65
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06041040 LTP 0x00000001) @ 0x1fffebd9
ACPI: DSDT (v001 IBM TP-A21m 0x06041040 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 20000000 (gap: 20000000:dff80000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
CPU 0 irqstacks, hard=c0453000 soft=c0452000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 996.667 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 513852k/524224k available (2512k kernel code, 9752k reserved, 684k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1978.36 BogoMIPS (lpj=989184)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f1ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs... it is
Freeing initrd memory: 1075k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: Power Resource [PSER] (on)
ACPI: Power Resource [PSIO] (on)
ACPI: Embedded Controller [EC] (gpe 9)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x1000-0x103f could not be reserved
pnp: 00:01: ioport range 0x1040-0x104f has been reserved
pnp: 00:01: ioport range 0xfe00-0xfe0f has been reserved
pnp: 00:08: ioport range 0x15e0-0x15ef has been reserved
Simple Boot Flag at 0x35 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1114937418.977:0): initialized
Total HugeTLB memory allocated, 0
con't...
|
2nd May 2005, 12:02 AM
|
|
Registered User
|
|
Join Date: Apr 2005
Location: Western Hemisphere
Posts: 13
|
|
Code:
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 2FE84E17A5733673
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Limiting direct PCI/PCI transfers.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (57 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:03.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ST960822A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 917504 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
LID SLPB PCI0 USB UART
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 176k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PS/2 Generic Mouse on isa0060/serio1
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
e100: Intel(R) PRO/100 Network Driver, 3.3.6-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
e100: eth0: e100_probe: addr 0xf4120000, irq 11, MAC addr 00:03:47:BA:D5:9A
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
gameport: CS46xx Gameport is pci0000:00:05.0/gameport0, speed 1864kHz
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: IBM Laptop detected; this module may corrupt your serial eeprom! Refusing to load module!
piix4_smbus: probe of 0000:00:07.3 failed with error -1
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001860
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66
usb 1-1: new low speed USB device using uhci_hcd and address 2
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e4520(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: IBM ThinkPad ACPI Extras v0.8
ibm_acpi: http://ibm-acpi.sf.net/
ibm_acpi: dock device not present
ibm_acpi: bay device not present
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
EXT3 FS on hda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 521632k swap on /dev/hda3. Priority:-1 extents:1
Thanks!
|
5th May 2005, 10:14 AM
|
|
Registered User
|
|
Join Date: Apr 2005
Posts: 2
|
|
Hi,
I've got the same problem. OSS works but ALSA doesn't. This occurred yesterday after updating my test release. Dmesg says following after trying to play mp3-file with XMMS with ALSA output:
Code:
Unable to handle kernel NULL pointer dereference at 0000000000000000 RIP:
<ffffffff880b1516>{:snd_timer:snd_timer_user_append_to_tqueue+38}
PGD ccb0067 PUD ccac067 PMD 0
Oops: 0002 [1]
CPU 0
Modules linked in: autofs4 ipt_REJECT ipt_state ip_conntrack iptable_filter ip_tables nls_utf8 ntfs video button battery ac md5 ipv6 ati_remote ohci_hcd ehci_hcd i2c_nforce2 i2c_core shpchp emu10k1_gp gameport snd_emu10k1 snd_rawmidi snd_ac97_codec snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc snd_util_mem snd_hwdep snd soundcore 3c59x mii sata_nv libata scsi_mod ext3 jbd
Pid: 2834, comm: xmms Not tainted 2.6.11
RIP: 0010:[<ffffffff880b1516>] <ffffffff880b1516>{:snd_timer:snd_timer_user_append_to_tqueue+38}
RSP: 0018:ffff81001ec3dd90 EFLAGS: 00010203
RAX: 7461636900000006 RBX: ffff81001d403d10 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff81001ec3dea8 RDI: ffff81001a278910
RBP: ffff81001a278910 R08: 0000000000000000 R09: ffffffff880b4f40
R10: 0000000000861ce0 R11: 0000000000000001 R12: 0000000041801870
R13: ffff81001ec3dda8 R14: 0000000040505412 R15: 0000000000940680
FS: 0000000041802960(005b) GS:ffffffff80500d40(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 000000000ccd5000 CR4: 00000000000006e0
Process xmms (pid: 2834, threadinfo ffff81001ec3c000, task ffff81001b24b810)
Stack: ffffffff880b5a9f ffff81001ffed380 ffffffff8017352f 0000000100000005
0000000000000000 0000000000008002 0000000000000000 0000000000000000
0000000000000000 0000000000000000
Call Trace:<ffffffff880b5a9f>{:snd_timer:snd_timer_user_ioctl+2911}
<ffffffff8017352f>{poison_obj+63} <ffffffff880932fa>{:snd:snd_open+266}
<ffffffff801a5213>{chrdev_open+915 <ffffffff80173db9>{cache_alloc_debugcheck_after+329}
<ffffffff8017352f>{poison_obj+63}<ffffffff80173c64>{cache_free_debugcheck+580}
<ffffffff801b1dac>{do_ioctl+76} <ffffffff801b20cf>{vfs_ioctl+783}
<ffffffff801b216c>{sys_ioctl+108} <ffffffff8010ec8e>{tracesys+209}
Code: 48 89 01 48 8b 46 08 48 89 41 08 48 8b 46 10 48 89 41 10 48
RIP <ffffffff880b1516>{:snd_timer:snd_timer_user_append_to_tqueue+38} RSP <ffff81001ec3dd90>
CR2: 0000000000000000
|
5th May 2005, 10:23 AM
|
 |
Registered User
|
|
Join Date: Nov 2004
Location: Netherlands
Age: 25
Posts: 1,426
|
|
|
Wich version of alsa do you have, try: rpm -aq | grep alsa
Are you sure sound isn't just muted, try: alsamixer
|
5th May 2005, 02:24 PM
|
|
Registered User
|
|
Join Date: Apr 2005
Posts: 2
|
|
Quote:
|
Originally Posted by bitrain
Wich version of alsa do you have, try: rpm -aq | grep alsa
Are you sure sound isn't just muted, try: alsamixer
|
Code:
$ rpm -aq | grep alsa
alsa-utils-1.0.9rc2-1
alsa-lib-1.0.9rc2-3
alsa-lib-1.0.9rc2-3
alsa-lib-devel-1.0.9rc2-3
Sound isn't muted.
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
Current GMT-time: 23:53 (Saturday, 18-05-2013)
|
|
 |
 |
 |
 |
|
|
