Lexmark driver sh - z600cups-1.0-1.gz sh wont unpack

[input]

I get this errror with unpacking

[root@localhost Downloads]# sh - z600cups-1.0-1.gz.sh
Verifying archive integrity...tail: cannot open `+6' for reading: No such file or directory
Error in check sums 2331425966 225780837

Has anybody some idea to solve this problem ?

[input]

Please help
Any one ?

[David Batson]

Error in checksums would seem to indicate a corrupted file. Try downloading again.

[input]

Thanks for the reply. I have download again but now I get this message
[root@localhost Downloads]# - sh z600cups-1.0-1.tar.gz.sh
bash: -: command not found...

[David Batson]

You have a hypen in front of sh. I believe that is your problem this time.

---------- Post added at 06:36 AM ---------- Previous post was at 06:30 AM ----------

If you still have problems, you might need to follow these instructions as well.

http://www.makeuseof.com/answers/ins...printer-linux/

[input]

I need to install this driver with - sh.
Here is the doc:

BASIC INSTALLATION
==================

Z600 CUPS Printer Driver includes the following files:
- z600cups-1.0-1.tar.gz.sh
- README
- COPYING

In general, to install Z600 CUPS Printer Driver, you run
the following command:
- sh z600cups-1.0-1.tar.gz.sh

but with - sh z600cups-1.0-1.tar.gz.sh I get bash command not found.

[PiElle]

In my opinion you should extract the file in the archive.
Then run:
./nomefile (from the directory in which you downloaded the file itself).
Or double-click on it and then choose run in a terminal ...
Hope it helps ...

[David Batson]

Originally Posted by input

I need to install this driver with - sh.
Here is the doc:

BASIC INSTALLATION
==================

Z600 CUPS Printer Driver includes the following files:
- z600cups-1.0-1.tar.gz.sh
- README
- COPYING

In general, to install Z600 CUPS Printer Driver, you run
the following command:
- sh z600cups-1.0-1.tar.gz.sh

but with - sh z600cups-1.0-1.tar.gz.sh I get bash command not found.

Of course. Look more carefully. A hypen precedes each line above. The hyphen is only being used as a bullet (point).

- z600cups-1.0-1.tar.gz.sh
- README
- COPYING

- sh z600cups-1.0-1.tar.gz.sh

[input]

Yes thanks.

but now I get this:

[root@localhost Downloads]# sh z600cups-1.0-1.gz.sh
Verifying archive integrity...tail: cannot open `+6' for reading: No such file or directory
Error in check sums 2331425966 225780837

[PiElle]

Are you sure is for rpm based distros?

[input]

On the site the say that it is tested on Redhat 9.0

[Dangermouse]

Use the commands below and you should end up with the two rpms

tail -n +143 z600cups-1.0-1.gz.sh > install.tar.gz
tar -xvzf install.tar.gz

If not ill give you link to the rpms

[input]

Thanks very much it gives me two rpms

[DCOH]

You need to install libstdc ++33 to get it to print, I know i used the Z600 series in FC7.

[input]

Originally Posted by DCOH

You need to install libstdc ++33 to get it to print, I know i used the Z600 series in FC7.

Where can I install this.

Thanks

---------- Post added at 01:24 PM ---------- Previous post was at 12:20 PM ----------

Yes it works how do you know it from libstdc ++33.

Many thanks