I am having an issue where my RAID isn't being mounted on boot. I get an error that comes up saying Unable to mount media: there is probably no media in the drive. Any insight on how to fix this?
EDIT:
Here is what I get when I do a fdisk -l
[root@repositorybackup ~]# fdisk -l
Disk /dev/sda: 37.0 GB, 37018484224 bytes
255 heads, 63 sectors/track, 4500 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 4500 36041827+ 8e Linux LVM
Disk /dev/sdb: 4998.2 GB, 4998257704960 bytes
255 heads, 63 sectors/track, 607670 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/sdb is what I am trying to open and get the error
fstab reads:
[root@repositorybackup ~]# cat /etc/fstab
/dev/VolGroup00/LogVol00 / ext3 defaults 1 1
LABEL=/boot /boot ext3 defaults 1 2
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
/dev/VolGroup00/LogVol01 swap swap defaults 0 0
dmesg reads:
PCI: Setting latency timer of device 0000:05:00.0 to 64
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:10.1 to 64
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
AAC0: kernel 5.2-0[16116]
AAC0: monitor 5.2-0[16116]
AAC0: bios 5.2-0[16116]
AAC0: serial 86aa8
AAC0: Non-DASD support enabled.
scsi6 : aacraid
scsi 6:0:0:0: Direct-Access Adaptec Repo Backup V1.0 PQ: 0 ANSI: 2
scsi 6:1:0:0: Direct-Access ST31000340AS AD14 PQ: 1 ANSI: 5
scsi 6:1:1:0: Direct-Access ST31000340AS AD14 PQ: 1 ANSI: 5
scsi 6:1:2:0: Direct-Access ST31000340AS AD14 PQ: 1 ANSI: 5
scsi 6:1:3:0: Direct-Access ST31000340AS AD14 PQ: 1 ANSI: 5
scsi 6:1:4:0: Direct-Access ST31000340AS AD14 PQ: 1 ANSI: 5
fw_core: created new fw device fw0 (0 config rom retries)
sdb : very big device. try to use READ CAPACITY(16).
SCSI device sdb: 9762222080 512-byte hdwr sectors (4998258 MB)
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
sdb : very big device. try to use READ CAPACITY(16).
SCSI device sdb: 9762222080 512-byte hdwr sectors (4998258 MB)
sdb: assuming Write Enabled
sdb: assuming drive cache: write through
sdb:
sd 6:0:0:0: Attached scsi removable disk sdb
sd 6:0:0:0: Attached scsi generic sg2 type 0
scsi 6:1:0:0: Attached scsi generic sg3 type 0
scsi 6:1:1:0: Attached scsi generic sg4 type 0
scsi 6:1:2:0: Attached scsi generic sg5 type 0
scsi 6:1:3:0: Attached scsi generic sg6 type 0
scsi 6:1:4:0: Attached scsi generic sg7 type 0
I am using a 36GB Wester Digital for the OS and 5 Seagate 1TB drives in the raid for backup storage.
Unable to mount media
Linear Mode
