FedoraForum.org - Fedora Support Forums and Community
Results 1 to 8 of 8
  1. 13th February 2008, 10:53 PM #1
    zakhmi
    zakhmi is offline Registered User
    Join Date
    Feb 2008
    Posts
    25
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    external hard disk

    i've 80GB external hard disk..however for some reason fedora 6 doen't recognize my hard disk..dmesg gives the following:
    usb 5-1: new high speed USB device using ehci_hcd and address 6
    usb 5-1: configuration #1 chosen from 1 choice
    Initializing USB Mass Storage driver...
    scsi1 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 6
    usb-storage: waiting for device to settle before scanning
    Vendor: WDC WD80 Model: 0BEVE-00UYT0 Rev: 0 0
    Type: Direct-Access ANSI SCSI revision: 00
    SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 03 00 00 00
    sdb: assuming drive cache: write through
    SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
    sdb: Write Protect is off
    sdb: Mode Sense: 03 00 00 00
    sdb: assuming drive cache: write through
    sdb:<6>sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    printk: 707 messages suppressed.
    Buffer I/O error on device sdb, logical block 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    Buffer I/O error on device sdb, logical block 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    Buffer I/O error on device sdb, logical block 0
    unable to read partition table
    sd 1:0:0:0: Attached scsi disk sdb
    sd 1:0:0:0: Attached scsi generic sg1 type 0
    usb-storage: device scan complete
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301312
    Buffer I/O error on device sdb, logical block 19537664
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301312
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301424
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301472
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301312
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301312
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301424
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301472
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 156301480
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    sd 1:0:0:0: SCSI error: return code = 0x10070000
    end_request: I/O error, dev sdb, sector 0
    [root@localhost ~]#
    plz help...
    Reply With Quote Reply With Quote
  2. 15th February 2008, 12:45 AM #2
    clay247 Guest
    Do errors happen when you attempt to mount the drive?

    Can you hook it to a windows machine and do a chkdsk /f

    C
    Reply With Quote Reply With Quote
  3. 15th February 2008, 12:49 AM #3
    JN4OldSchool
    JN4OldSchool is offline "Sean The Terrible" -- The forum(er) Vista® rep
    Join Date
    Nov 2005
    Posts
    8,819
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by clay247
    Do errors happen when you attempt to mount the drive?

    Can you hook it to a windows machine and do a chkdsk /f

    C
    WTF? A WINDOWS machine?
    Reply With Quote Reply With Quote
  4. 15th February 2008, 12:52 AM #4
    clay247 Guest
    Sorry again, am I being unclear? A window computer, is that better? He is trying to troubleshoot and I'm trying to help. Doesn't look like you have a better idea.
    Reply With Quote Reply With Quote
  5. 15th February 2008, 12:56 AM #5
    JN4OldSchool
    JN4OldSchool is offline "Sean The Terrible" -- The forum(er) Vista® rep
    Join Date
    Nov 2005
    Posts
    8,819
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quote Originally Posted by clay247
    Sorry again, am I being unclear? A window computer, is that better? He is trying to troubleshoot and I'm trying to help. Doesn't look like you have a better idea.
    No, I dont. But listen boywonder, so far you have chalked up 35 posts asking asinine questions, suggesting the poster look elsewhere for answers of just babbling some irrelevant code that makes no sense and has nothing whatsoever to do with the problem. Now you want the poster to go find a Windows computer? Ah, most of us, when we dont know the answer, will just refrain from posting so that the person who DOES have the answer can work with the poster. You are making quite a name for yourself in just a few hours.
    Reply With Quote Reply With Quote
  6. 15th February 2008, 09:49 PM #6
    zakhmi
    zakhmi is offline Registered User
    Join Date
    Feb 2008
    Posts
    25
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    nothing happens when i connect my usb external hard disk to my laptop..its working fine on windows..after dmesg i got the above pasted errors...
    Reply With Quote Reply With Quote
  7. 15th February 2008, 10:00 PM #7
    clay247 Guest
    I found the idea of trying chkdsk /f using windows to troubleshoot in another post related to using a NTFS filesystem with Linux. Was/is your USB drive formatted NTFS? Did you try the chkdisk /f when you hooked it up to windows? The command will be chkdisk /f F: assuming your drive pops up as F:

    I'm talking about using windows cmd prompt to run the command.

    I hate to post this for fear of being attacked again.
    Reply With Quote Reply With Quote
  8. 17th February 2008, 10:15 PM #8
    zakhmi
    zakhmi is offline Registered User
    Join Date
    Feb 2008
    Posts
    25
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    i solved the problem by upgrading to fedora 7.. i read somewhere that f6 has problem in recognizing ext. hard disk; dat depends on d kernel used..nyway thanks for your suggestion
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. External Hard Disk not detected
    By nardneran in forum Hardware
    Replies: 1
    Last Post: 8th May 2008, 08:09 PM
  2. FC7 cant mount external hard disk
    By Kaanx in forum Using Fedora
    Replies: 3
    Last Post: 12th August 2007, 07:57 PM
  3. usb 2 external hard disk
    By dwisianto in forum Hardware
    Replies: 1
    Last Post: 8th July 2005, 10:43 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

User Tag List