Hi,
I successfully attach a range of USB devices to a machine running Fedora 7. The only device that has a problem attaching is a Windows Mobile 5 PDA (TMobile MDA Vario 2 = HTC device). I expect to see the device under Nautilus file manager as some kind of disk drive - but the PDA is not visible in Nautilus - I think the problem is "lower" in device detection and support. This device was supported under Fedora 5 kernel 2.6.something.
Is there a known bug and/or fix for this? Any idea what is causing this? Should I raise a bug? (never done that before).
The messages from dmesg are below.
Failing USB device : USB attached PDA (TMobile MDA Vario 2 = HTC device) running Windows mobile 5
usb 1-1.4: new full speed USB device using ohci_hcd and address 12
usb 1-1.4: configuration #1 chosen from 1 choice
eth2: register 'rndis_host' at usb-0000:00:03.0-1.4, RNDIS device, 80:00:60:0f:e8:00
eth2: unregister 'rndis_host' usb-0000:00:03.0-1.4, RNDIS device
usb 1-1.4: usbfs: interface 0 claimed by usbfs while 'vmware-vmx' sets config #1
usb 1-2: ZC0301[P] Image Processor and Control Chip detected (vid/pid 0x0AC8:0x301B)
usb 1-2: No supported image sensor detected
rndis_host: probe of 1-1.4:1.0 failed with error -16
usb 1-2: ZC0301[P] Image Processor and Control Chip detected (vid/pid 0x0AC8:0x301B)
usb 1-2: No supported image sensor detected
rndis_host 1-1.4:1.0: RNDIS init failed, -110
rndis_host: probe of 1-1.4:1.0 failed with error -110
usb 1-1.4: USB disconnect, address 12
usb 1-1.4: new full speed USB device using ohci_hcd and address 13
usb 1-1.4: device descriptor read/64, error -110
usb 1-1.4: device descriptor read/64, error -110
usb 1-1.4: new full speed USB device using ohci_hcd and address 14
usb 1-1.4: device descriptor read/64, error -110
usb 1-1.4: device descriptor read/64, error -110
usb 1-1.4: new full speed USB device using ohci_hcd and address 15
... and so on. Last few message repeat over time as address increases: 16, 17, 18 , ...
Successful devices
USB 4 port hub
usb 1-1: new full speed USB device using ohci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
USB optical mouse
usb 1-1.2: new low speed USB device using ohci_hcd and address 5
usb 1-1.2: configuration #1 chosen from 1 choice
input: Microsoft Microsoft Trackball Optical� as /class/input/input9
input: USB HID v1.00 Mouse [Microsoft Microsoft Trackball Optical�] on usb-0000:00:03.0-1.2
USB headphones
usb 1-1.1: new full speed USB device using ohci_hcd and address 6
usb 1-1.1: configuration #1 chosen from 1 choice
input: C-Media USB Headphone Set as /class/input/input10
input: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-0000:00:03.0-1.1
usbcore: registered new interface driver snd-usb-audio
USB printer
usb 3-1: new full speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x0482 pid 0x0003
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
USB scanner
usb 1-1.3: new full speed USB device using ohci_hcd and address 7
usb 1-1.3: configuration #1 chosen from 1 choice
USB disk drive
usb 1-1.3: configuration #1 chosen from 1 choice
usb 4-2: new high speed USB device using ehci_hcd and address 5
usb 4-2: configuration #1 chosen from 1 choice
hub 4-2:1.0: USB hub found
hub 4-2:1.0: 4 ports detected
usb 4-2.4: new high speed USB device using ehci_hcd and address 6
usb 4-2.4: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb 4-2.2: new high speed USB device using ehci_hcd and address 7
usb 4-2.2: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
hiddev96: USB HID v1.10 Device [Western Digital External HDD] on usb-0000:00:03.3-2.2
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access WD CR HS-CF 3.04 PQ: 0 ANSI: 0
scsi 2:0:0:1: Direct-Access WD CR HS-5-IN-1 3.04 PQ: 0 ANSI: 0
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:1: Attached scsi removable disk sdc
sd 2:0:0:1: Attached scsi generic sg3 type 0
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access WD 2500JB External 0112 PQ: 0 ANSI: 0
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 33 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 33 00 00 00
sdd: assuming drive cache: write through
sdd: sdd1
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg4 type 0
Linear Mode
