Hmmm I see. Does it help to make an address static? Currently for me its 10.1.1.3 , static it up? And looking at code below. What is virbr0? should it not say 10.1.1.1 - ip of my router?
eth0 Link encap:Ethernet HWaddr 00:1F0:21:2B:FD
inet addr:10.1.1.3 Bcast:10.255.255.255 Mask:255.0.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7769 errors:0 dropped:0 overruns:0 frame:0
TX packets:8098 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5469367 (5.2 MiB) TX bytes:1514845 (1.4 MiB)
Interrupt:33 Base address:0x2000
eth1 Link encap:Ethernet HWaddr 00:1F0:21:2D:4D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:34
eth2 Link encap:Ethernet HWaddr 00:1F0:21:29:6D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:35 Base address:0x4000
eth3 Link encap:Ethernet HWaddr 00:1F0:21:31:FD
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:36 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:22 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1100 (1.0 KiB) TX bytes:1100 (1.0 KiB)
virbr0 Link encap:Ethernet HWaddr B2:FC:81:9E

6:81
inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:15322 (14.9 KiB)
---------- Post added at 02:00 PM CST ---------- Previous post was at 11:53 AM CST ----------
Going to install NetworkManager 0.7.998 according to
http://forums.fedoraforum.org/showpo...5&postcount=12
However, when configure the downloaded package -
configure: error: wireless-tools library and development headers >= 28pre9 not installed or not functional
Any Ideas?
---------- Post added at 10:57 PM CST ---------- Previous post was at 02:00 PM CST ----------
Changed to 'vanilla' 2.6.32.4' kernel.
Testing, i hope this fixes it.