JuanCarlos
16th November 2004, 02:38 PM
Hello everybody.
I am just starting as a user of this forum, and y hope to be able to provide some help where I could.
I'm having some problems when I try to mount my memory stick. I'm running Fedora Core 3 and 2.6.9 kernel. When I plug the memory stick this error is thrown:
usb 1-1: new full speed USB device using address 2
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: JetFlash Model: TS1GJF2C Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
sda: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda:<6>usb 1-1: reset full speed USB device using address 2
usb 1-1: control timeout on ep0in
usb 1-1: device not accepting address 2, error -71
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
SCSI error : <0 0 0 0> return code = 0x50000
end_request: I/O error, dev sda, sector 2097144
Buffer I/O error on device sda, logical block 262143
scsi0 (0:0): rejecting I/O to offline device
scsi0 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda, logical block 262143
sda1
usb 1-1: USB disconnect, address 2
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
sd 0:0:0:0: Illegal state transition cancel->offline
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1688
[<12a17645>] scsi_device_set_state+0xc8/0xd3 [scsi_mod]
[<12a14b8b>] scsi_eh_offline_sdevs+0x49/0x5e [scsi_mod]
[<12a15146>] scsi_unjam_host+0x22d/0x23e [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
sd 0:0:0:0: Illegal state transition cancel->offline
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1688
[<12a17645>] scsi_device_set_state+0xc8/0xd3 [scsi_mod]
[<12a14b8b>] scsi_eh_offline_sdevs+0x49/0x5e [scsi_mod]
[<12a15146>] scsi_unjam_host+0x22d/0x23e [scsi_mod]
[<12a115c5>] __scsi_iterate_devices+0x123/0x12b [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
Unable to handle kernel NULL pointer dereference at virtual address 00000008
printing eip:
0224fb8f
*pde = 00000000
Oops: 0000 [#1]
Modules linked in: vfat fat sd_mod usb_storage scsi_mod lp autofs4 i2c_dev i2c_core sunrpc microcode dm_mod uhci_hcd parport_pc parport snd_via82xx snd_ac97_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc gameport snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore 8139too mii floppy ext3 jbd
CPU: 0
EIP: 0060:[<0224fb8f>] Not tainted VLI
EFLAGS: 00010046 (2.6.9-1.667)
EIP is at cfq_insert_request+0x45/0xdf
eax: 11c384b8 ebx: 033cd4b0 ecx: 00000001 edx: 033cd4b0
esi: 00000001 edi: 00000000 ebp: 00000000 esp: 027ddefc
ds: 007b es: 007b ss: 0068
Process scsi_eh_0 (pid: 4667, threadinfo=027dd000 task=10c1e1f0)
Stack: 11c384b8 11c384b8 00000001 033cd4b0 00000202 02246367 11c384b8 00000001
033cd4b0 02246329 00000000 022484d8 0b628ac0 0e578000 0bd66000 00001057
12a15576 0b628ac0 00000001 0b628ac0 027ddf74 027ddf74 027ddf7c 12a14ec8
Call Trace:
[<02246367>] __elv_add_request+0x3c/0x71
[<02246329>] elv_requeue_request+0x29/0x2b
[<022484d8>] blk_insert_request+0xba/0x18b
[<12a15576>] scsi_queue_insert+0x84/0x8d [scsi_mod]
[<12a14ec8>] scsi_eh_flush_done_q+0x7d/0xce [scsi_mod]
[<12a1514f>] scsi_unjam_host+0x236/0x23e [scsi_mod]
[<12a115c5>] __scsi_iterate_devices+0x123/0x12b [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
Code: 74 29 eb 51 83 f9 03 74 33 eb 4a 8b 04 24 89 fa e8 f8 fa ff ff 85 c0 75 f2 8b 47 08 8b 50 04 89 03 89 58 04 89 1a 89 53 04 eb 3f <8b> 47 08 8b 10 89 5a 04 89 13 89 43 04 89 18 eb 2e f6 42 08 10
Does anybody know the way to solve it?
Thanks in advance.
Juan Carlos
I am just starting as a user of this forum, and y hope to be able to provide some help where I could.
I'm having some problems when I try to mount my memory stick. I'm running Fedora Core 3 and 2.6.9 kernel. When I plug the memory stick this error is thrown:
usb 1-1: new full speed USB device using address 2
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: JetFlash Model: TS1GJF2C Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
sda: Unit Not Ready, sense:
Current : sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Unit Attention
Additional sense: Not ready to ready change, medium may have changed
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda:<6>usb 1-1: reset full speed USB device using address 2
usb 1-1: control timeout on ep0in
usb 1-1: device not accepting address 2, error -71
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
SCSI error : <0 0 0 0> return code = 0x50000
end_request: I/O error, dev sda, sector 2097144
Buffer I/O error on device sda, logical block 262143
scsi0 (0:0): rejecting I/O to offline device
scsi0 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda, logical block 262143
sda1
usb 1-1: USB disconnect, address 2
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
sd 0:0:0:0: Illegal state transition cancel->offline
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1688
[<12a17645>] scsi_device_set_state+0xc8/0xd3 [scsi_mod]
[<12a14b8b>] scsi_eh_offline_sdevs+0x49/0x5e [scsi_mod]
[<12a15146>] scsi_unjam_host+0x22d/0x23e [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
sd 0:0:0:0: Illegal state transition cancel->offline
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1688
[<12a17645>] scsi_device_set_state+0xc8/0xd3 [scsi_mod]
[<12a14b8b>] scsi_eh_offline_sdevs+0x49/0x5e [scsi_mod]
[<12a15146>] scsi_unjam_host+0x22d/0x23e [scsi_mod]
[<12a115c5>] __scsi_iterate_devices+0x123/0x12b [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
Unable to handle kernel NULL pointer dereference at virtual address 00000008
printing eip:
0224fb8f
*pde = 00000000
Oops: 0000 [#1]
Modules linked in: vfat fat sd_mod usb_storage scsi_mod lp autofs4 i2c_dev i2c_core sunrpc microcode dm_mod uhci_hcd parport_pc parport snd_via82xx snd_ac97_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc gameport snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore 8139too mii floppy ext3 jbd
CPU: 0
EIP: 0060:[<0224fb8f>] Not tainted VLI
EFLAGS: 00010046 (2.6.9-1.667)
EIP is at cfq_insert_request+0x45/0xdf
eax: 11c384b8 ebx: 033cd4b0 ecx: 00000001 edx: 033cd4b0
esi: 00000001 edi: 00000000 ebp: 00000000 esp: 027ddefc
ds: 007b es: 007b ss: 0068
Process scsi_eh_0 (pid: 4667, threadinfo=027dd000 task=10c1e1f0)
Stack: 11c384b8 11c384b8 00000001 033cd4b0 00000202 02246367 11c384b8 00000001
033cd4b0 02246329 00000000 022484d8 0b628ac0 0e578000 0bd66000 00001057
12a15576 0b628ac0 00000001 0b628ac0 027ddf74 027ddf74 027ddf7c 12a14ec8
Call Trace:
[<02246367>] __elv_add_request+0x3c/0x71
[<02246329>] elv_requeue_request+0x29/0x2b
[<022484d8>] blk_insert_request+0xba/0x18b
[<12a15576>] scsi_queue_insert+0x84/0x8d [scsi_mod]
[<12a14ec8>] scsi_eh_flush_done_q+0x7d/0xce [scsi_mod]
[<12a1514f>] scsi_unjam_host+0x236/0x23e [scsi_mod]
[<12a115c5>] __scsi_iterate_devices+0x123/0x12b [scsi_mod]
[<12a15291>] scsi_error_handler+0x13a/0x191 [scsi_mod]
[<0211b3d9>] schedule_tail+0xc/0x37
[<12a15157>] scsi_error_handler+0x0/0x191 [scsi_mod]
[<021041d9>] kernel_thread_helper+0x5/0xb
Code: 74 29 eb 51 83 f9 03 74 33 eb 4a 8b 04 24 89 fa e8 f8 fa ff ff 85 c0 75 f2 8b 47 08 8b 50 04 89 03 89 58 04 89 1a 89 53 04 eb 3f <8b> 47 08 8b 10 89 5a 04 89 13 89 43 04 89 18 eb 2e f6 42 08 10
Does anybody know the way to solve it?
Thanks in advance.
Juan Carlos
