gcell
10th April 2009, 06:34 AM
My N6270 cellpone(Nokia) has a cardreader inside ,and could be used as a USB Mass Storage though USB data serial when SD card inserted .
now system can recognize this device ,but can't mount it in Fedora 11 rawhide .
dmesg tells me some infos:
[xelnaga@ASUS6 ~]$ dmesg |tail -n 30
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
IRQ 16/nvidia: IRQF_DISABLED is not guaranteed on shared IRQs
eth0: no IPv6 routers present
fuse init (API version 7.11)
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: New USB device found, idVendor=0421, idProduct=043e
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: Nokia 6270
usb 2-1: Manufacturer: Nokia
usb 2-1: SerialNumber: 357579006915807
usb 2-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access Nokia Nokia 6270 0000 PQ: 0 ANSI: 4
sd 2:0:0:0: [sdb] 1950720 512-byte hardware sectors: (998 MB/952 MiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 1950720 512-byte hardware sectors: (998 MB/952 MiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb:
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
[xelnaga@ASUS6 ~]$
I would like someone can help me, Thank you guys!
PS: it work well on win XP, not a hardware problem.
https://bugzilla.redhat.com/show_bug.cgi?id=495178
now system can recognize this device ,but can't mount it in Fedora 11 rawhide .
dmesg tells me some infos:
[xelnaga@ASUS6 ~]$ dmesg |tail -n 30
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
IRQ 16/nvidia: IRQF_DISABLED is not guaranteed on shared IRQs
eth0: no IPv6 routers present
fuse init (API version 7.11)
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: New USB device found, idVendor=0421, idProduct=043e
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1: Product: Nokia 6270
usb 2-1: Manufacturer: Nokia
usb 2-1: SerialNumber: 357579006915807
usb 2-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access Nokia Nokia 6270 0000 PQ: 0 ANSI: 4
sd 2:0:0:0: [sdb] 1950720 512-byte hardware sectors: (998 MB/952 MiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 1950720 512-byte hardware sectors: (998 MB/952 MiB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb:
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
[xelnaga@ASUS6 ~]$
I would like someone can help me, Thank you guys!
PS: it work well on win XP, not a hardware problem.
https://bugzilla.redhat.com/show_bug.cgi?id=495178
