install help oops 2 [1]

[mmaleh]

so I did an install on a dual processor p4 600mhz with 512 RAM I gave my swap partition 700mb. Upon reboot it hung on enabling swap space at that point I thought maybe the scsi card I had in the machine might be confusing things so I took that out. now it hangs at a different spot:
after Enabling swap space - OK
oops: 0002 [#1]
smp
cpu : 1
EIP : 0060:[<021a2aad>]
bunch of other stuff....
stack:......
Call Trace:
5 lines of
kobject_register
bus_add_driver
pci_register_driver
natsemi_init_mod
sys_init_module
code: 89 11 89 4a 04 8b 47 28 8b 18 8d 48 89 c8 ba ff ff 00 00

I am new to this so any help would be most appreciated. if you need any other sections in detail I can expand. Thanks.
-marc maleh

[tashirosgt]

The first questions that pop into my mind:

What happens when you put the scsi car back in? Does it hang at enabling swap space? How bad a hang is it? Does the hard driive activity light blink? Does the numlock led turn off and on when you press the numlock key?

[mmaleh]

With the card back in it hangs at swap space. the hard drive light will blink for a little while and num lock will work for a min or two then it will totally crash.
with the card not in it will hang for like 4 min at the code: 89 11 89 4a 04 8b 47 28 8b 18 8d 48 89 c8 ba ff ff 00 00
then the screen goes black.
thanks!

[mmaleh]

currently I am trying knoppix to see if it will run linux off the CD. seems to run fine.

[tashirosgt]

Can you use knoppix to look at /var/log/boot.log on your FC2 installation?
and /var/log/dmesg

[mmaleh]

I will try and get back to you. Thanks!
-m

[mmaleh]

I was able to get to the dmesg. it said I did not have permissions to see my boot.log. I will try again though. see below for the dmesg. thanks!
Linux version 2.6.5-1.358smp (bhcompile@bugs.build.redhat.com) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 SMP Sat May 8 09:25:36 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fffc000 (usable)
BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
ACPI: S3 and PAE do not like each other for now, S3 disabled.
found SMP MP-table at 000f5460
On node 0 totalpages: 131068
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126972 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 ASUS ) @ 0x000f6740
ACPI: RSDT (v001 ASUS CUV4X-D 0x30303031 MSFT 0x31313031) @ 0x1fffc000
ACPI: FADT (v001 ASUS CUV4X-D 0x30303031 MSFT 0x31313031) @ 0x1fffc100
ACPI: BOOT (v001 ASUS CUV4X-D 0x30303031 MSFT 0x31313031) @ 0x1fffc040
ACPI: MADT (v001 ASUS CUV4X-D 0x30303031 MSFT 0x31313031) @ 0x1fffc080
ACPI: DSDT (v001 ASUS CUV4X-D 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x03] enabled)
Processor #3 6:8 APIC version 17
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
1

[mmaleh]

Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet single
mapped 4G/4G trampoline to fffeb000.
Initializing CPU#0
CPU 0 irqstacks, hard=023ae000 soft=0238e000
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 600.211 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 514876k/524272k available (1676k kernel code, 8648k reserved, 708k data, 180k init, 0k highmem)
Calibrating delay loop... 1187.84 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
Failure registering capabilities with the kernel
selinux_register_security: Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f3ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU0: Intel Pentium III (Coppermine) stepping 06
per-CPU timeslice cutoff: 731.50 usecs.
task migration cache decay timeout: 1 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/0 eip 2000
CPU 1 irqstacks, hard=023af000 soft=0238f000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1196.03 BogoMIPS
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f3ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 06
Total of 2 processors activated (2383.87 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 599.0921 MHz.
..... host bus clock speed is 79.0989 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
zapping low mappings.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0cc0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
IOAPIC[0]: Set PCI routing entry (2-11 -> 0x81 -> IRQ 11 Mode:1 Active:1)
00:00:04[A] -> 2-11 -> IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
IOAPIC[0]: Set PCI routing entry (2-10 -> 0x79 -> IRQ 10 Mode:1 Active:1)
00:00:04[B] -> 2-10 -> IRQ 10
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:0c[A] -> 2-16 -> IRQ 169
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:0c[B] -> 2-17 -> IRQ 177
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:0c[C] -> 2-18 -> IRQ 185
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:0c[D] -> 2-19 -> IRQ 193
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178011
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 0FF 0F 0 0 0 0 0 1 1 39
02 0FF 0F 0 0 0 0 0 1 1 31
03 0FF 0F 0 0 0 0 0 1 1 41
04 0FF 0F 0 0 0 0 0 1 1 49
05 0FF 0F 0 0 0 0 0 1 1 51
06 0FF 0F 0 0 0 0 0 1 1 59
07 0FF 0F 0 0 0 0 0 1 1 61
08 0FF 0F 0 0 0 0 0 1 1 69
09 0FF 0F 0 1 0 1 0 1 1 71
0a 003 03 1 1 0 1 0 1 1 79
0b 003 03 1 1 0 1 0 1 1 81
0c 0FF 0F 0 0 0 0 0 1 1 89
0d 0FF 0F 0 0 0 0 0 1 1 91
0e 0FF 0F 0 0 0 0 0 1 1 99
0f 0FF 0F 0 0 0 0 0 1 1 A1
10 003 03 1 1 0 1 0 1 1 A9
11 003 03 1 1 0 1 0 1 1 B1
12 003 03 1 1 0 1 0 1 1 B9
13 003 03 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1094551058.4294966966:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
PCI: Enabling Via external APIC routing
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1, 16 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 32M @ 0xfc000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD400BB-75CAA0, ATA DISK drive
hda: IRQ probe failed (0xfffffcfa)
hdb: IOMEGA ZIP 250 ATAPI Floppy, ATAPI FLOPPY drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TDK CDRW161040, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 78125000 sectors (40000 MB)
native capacity is 78125040 sectors (40000 MB)
hda: 78125000 sectors (40000 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: hda1 hda2
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdb: No disk in drive
hdb: 0kB, 0/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
usbcore: registered new driver hiddev
usbcore: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Initializing IPsec netlink socket

[mmaleh]

NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S4 S5)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 186k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 180k freed
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
ACPI: Power Button (FF) [PWRF]
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:04.2: UHCI Host Controller
uhci_hcd 0000:00:04.2: irq 10, io base 0000d400
uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:04.3: UHCI Host Controller
uhci_hcd 0000:00:04.3: irq 10, io base 0000d000
uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
EXT3 FS on hda1, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
cdrom: open failed.
ide-floppy: hdb: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdb: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdb: No disk in drive
Adding 716680k swap on /dev/hda2. Priority:-1 extents:

[james_in_denver]

Looking at my "dmesg" I see that the only hardware devices that get initialized after swap is added are my parallel port and my network. here are a few things you might try.

#1, Disable your parallel port in your computer's BIOS settings, did that fix/change anything?

#2, Disable your network adaptor in your computer's BIOS settings (or physically remove the card with the machine turned off) (my lawyer made me add that last part). boot, did that fix/change anything?

#3, touch a key to get into the grub "boot" menu, "a"ppend this to the boot command line you are using "single noapci"...

#4 Disconnect the IDE cable from your "ZIP" drive and try rebooting.....

Let me know how it goes!.....

[tashirosgt]

My single processor machine completes the line with
Adding 10483312k swap on /dev/hda3. Priority:-1 extents:1
My suggestions would be to try to boot with a noswap option, just to see if it is indeed the swap or something after the enabling swap.


Some web research makes it look like your problem is usuallly not the swap but something after that step.
Unfortuately, which thing that is seems to vary and why certain solutions work is usually not explained.

Some suggestions were given by:
http://www.fedoraforum.org/forum/showthread.php?t=22763

This message claims the problem was fixed by using a non-graphical boot:
http://www.redhat.com/archives/fedora-list/2004-October/msg04992.html

Various suggestions:
http://www.linuxforums.org/forum/viewtopic.php?p=107909