SD, MMC, XD flash memory reader on Acer TravelMate 2492NWLMi

[jpm_power]

There is no automount if I put XD memory in that port (it works under WinXP) and also I don't know how to mount it manually. Is it possible to use it?

lspci -v

06:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
Subsystem: Acer Incorporated [ALI] Device 0090
Flags: bus master, medium devsel, latency 168, IRQ 16
Memory at d0004000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 8c000000-8ffff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

06:04.1 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller (rev 01)
Subsystem: Acer Incorporated [ALI] Device 0090
Flags: medium devsel, IRQ 11
Memory at d0005000 (32-bit, non-prefetchable) [disabled] [size=128]
Capabilities: [80] Power Management version 2

06:04.2 SD Host controller: ENE Technology Inc ENE PCI Secure Digital Card Reader Controller (rev 01) (prog-if 01)
Subsystem: Acer Incorporated [ALI] Device 0090
Flags: medium devsel, IRQ 17
Memory at d0005400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

06:04.3 FLASH memory: ENE Technology Inc FLASH memory: ENE Technology Inc: (rev 01)
Subsystem: Acer Incorporated [ALI] Device 0090
Flags: medium devsel, IRQ 11
Memory at d0005800 (32-bit, non-prefetchable) [disabled] [size=128]
Capabilities: [80] Power Management version 2

06:04.4 FLASH memory: ENE Technology Inc SD/MMC Card Reader Controller (rev 01)
Subsystem: Acer Incorporated [ALI] Device 0090
Flags: medium devsel, IRQ 17
Memory at d0005100 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci


dmesg | grep sdhci
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:06:04.2: SDHCI controller found [1524:0550] (rev 1)
sdhci-pci 0000:06:04.2: enabling device (0000 -> 0002)
sdhci-pci 0000:06:04.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
sdhci-pci 0000:06:04.4: SDHCI controller found [1524:0551] (rev 1)
sdhci-pci 0000:06:04.4: enabling device (0000 -> 0002)
sdhci-pci 0000:06:04.4: PCI INT B -> GSI 17 (level, low) -> IRQ 17


dmesg | grep mmc
Registered led device: mmc0
mmc0: SDHCI controller on PCI [0000:06:04.2] using PIO
Registered led device: mmc1
mmc1: SDHCI controller on PCI [0000:06:04.4] using PIO

[ryptyde]

I had a problem with an Acer running F10 that wouldn't mount an SDHC Extreme III card then after an update it works fine. My Sony desktop running F9 does not detect the card.