Enigma 2100
2006-12-30, 08:56 AM CST
I have just installed Fedora 6 onto a SCSI driive. I am trying to access a RAID0 on the same computer. The RAID is using the intel 875P chip on a Asus P4C800-E deluxe mobo. It is also ntfs. I have installed the ntfs drivers but dont know how the mount the RAID.
Update
Its the letter ID I need that references the RAID. If primary IDE is hda1 (secondary hda2 and so on) and first SCSI is sda1 (second SCSI sda2 and so on). What would RAID0 be? I did dmesg and I can see both drives which make up the RAID0 but the ID only shows each individual drive not the RAID. I have put most of the dmesg output here. You can see that the two drives which make up the RAID get listed twice as ata1 and ata2 and then again as sdb and sdc. Also further down you can see "autodedcting RAID arrays" comes up so I must just need the letter that fedora uses. What other commands would show the RAID0.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i875 Chipset.
agpgart: AGP aperture is 128M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y120P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PREMIUM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: MAT****A Model: DVD-RAM LF-D200 Rev: X120
Type: CD-ROM ANSI SCSI revision: 04
target0:0:4: Beginning Domain Validation
target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 32)
target0:0:4: Domain Validation skipping write tests
target0:0:4: Ending Domain Validation
Vendor: IBM Model: IC35L036UWD210-0 Rev: S5CQ
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 4
target0:0:6: Beginning Domain Validation
target0:0:6: wide asynchronous
target0:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:6: Ending Domain Validation
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:6:0: Attached scsi disk sda
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 169
ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 169
scsi1 : ata_piix
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi2 : ata_piix
ata2.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 < >
sd 1:0:0:0: Attached scsi disk sdb
Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: unknown partition table
sd 2:0:0:0: Attached scsi disk sdc
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1167496402.383:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1583 types, 172 bools, 1 sens, 1024 cats
security: 59 classes, 49428 rules
audit(1167496402.554:3): policy loaded auid=4294967295
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
ieee1394: Initialized config rom entry `ip1394'
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:01.0 to 64
e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:a6:5a:96:bf
intel_rng: FWH not detected
EDAC MC: Ver: 2.0.1 Dec 15 2006
input: PC Speaker as /class/input/input4
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:03:0a.2[b] -> GSI 23 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[193] MMIO=[feafe800-feafefff] Max Packet=[2048] IR/IT contexts=[4/8]
gameport: EMU10K1 is pci0000:03:0a.1/gameport0, io 0xdfe0, speed 1169kHz
ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 209
scsi 0:0:4:0: Attached scsi generic sg0 type 5
sd 0:0:6:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: Attached scsi generic sg3 type 0
EDAC i82875p: i82875p init one
EDAC MC0: Giving out device to i82875p_edac i82875p: DEV 0000:00:00.0
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sr0: scsi3-mmc drive: 0x/0x dvd-ram cd/rw xa/form2 cdda tray
sr 0:0:4:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 217
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c0020000c45]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
Vendor: Model: USB Flash Memory Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
sdd: assuming drive cache: write through
sdd: sdd1
sd 3:0:0:0: Attached scsi removable disk sdd
sd 3:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.4 loaded
EXT3 FS on dm-5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
SELinux: initialized (dev sdd1, type vfat), uses genfs_contexts
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS-fs error (device hda1): parse_options(): Unrecognized mount option unmask.
NTFS volume version 3.1.
SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts
NTFS volume version 3.1.
SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts
Update
Its the letter ID I need that references the RAID. If primary IDE is hda1 (secondary hda2 and so on) and first SCSI is sda1 (second SCSI sda2 and so on). What would RAID0 be? I did dmesg and I can see both drives which make up the RAID0 but the ID only shows each individual drive not the RAID. I have put most of the dmesg output here. You can see that the two drives which make up the RAID get listed twice as ata1 and ata2 and then again as sdb and sdc. Also further down you can see "autodedcting RAID arrays" comes up so I must just need the letter that fedora uses. What other commands would show the RAID0.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i875 Chipset.
agpgart: AGP aperture is 128M @ 0xf0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y120P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PLEXTOR DVDR PX-708A, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PREMIUM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 29160N Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: MAT****A Model: DVD-RAM LF-D200 Rev: X120
Type: CD-ROM ANSI SCSI revision: 04
target0:0:4: Beginning Domain Validation
target0:0:4: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 32)
target0:0:4: Domain Validation skipping write tests
target0:0:4: Ending Domain Validation
Vendor: IBM Model: IC35L036UWD210-0 Rev: S5CQ
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 4
target0:0:6: Beginning Domain Validation
target0:0:6: wide asynchronous
target0:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63)
target0:0:6: Ending Domain Validation
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
sda: Write Protect is off
sda: Mode Sense: cb 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:6:0: Attached scsi disk sda
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF90 irq 169
ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF98 irq 169
scsi1 : ata_piix
ata1.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi2 : ata_piix
ata2.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 < >
sd 1:0:0:0: Attached scsi disk sdb
Vendor: ATA Model: Maxtor 7Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: unknown partition table
sd 2:0:0:0: Attached scsi disk sdc
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1167496402.383:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1583 types, 172 bools, 1 sens, 1024 cats
security: 59 classes, 49428 rules
audit(1167496402.554:3): policy loaded auid=4294967295
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
ieee1394: Initialized config rom entry `ip1394'
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:01.0 to 64
e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:a6:5a:96:bf
intel_rng: FWH not detected
EDAC MC: Ver: 2.0.1 Dec 15 2006
input: PC Speaker as /class/input/input4
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:03:0a.2[b] -> GSI 23 (level, low) -> IRQ 193
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[193] MMIO=[feafe800-feafefff] Max Packet=[2048] IR/IT contexts=[4/8]
gameport: EMU10K1 is pci0000:03:0a.1/gameport0, io 0xdfe0, speed 1169kHz
ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 209
scsi 0:0:4:0: Attached scsi generic sg0 type 5
sd 0:0:6:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: Attached scsi generic sg3 type 0
EDAC i82875p: i82875p init one
EDAC MC0: Giving out device to i82875p_edac i82875p: DEV 0000:00:00.0
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
sr0: scsi3-mmc drive: 0x/0x dvd-ram cd/rw xa/form2 cdda tray
sr 0:0:4:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 22 (level, low) -> IRQ 217
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c0020000c45]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
Vendor: Model: USB Flash Memory Rev: 1.04
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
sdd: assuming drive cache: write through
SCSI device sdd: 1001472 512-byte hdwr sectors (513 MB)
sdd: Write Protect is off
sdd: Mode Sense: 23 00 00 00
sdd: assuming drive cache: write through
sdd: sdd1
sd 3:0:0:0: Attached scsi removable disk sdd
sd 3:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.4 loaded
EXT3 FS on dm-5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
SELinux: initialized (dev sdd1, type vfat), uses genfs_contexts
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS-fs error (device hda1): parse_options(): Unrecognized mount option unmask.
NTFS volume version 3.1.
SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts
NTFS volume version 3.1.
SELinux: initialized (dev hda1, type ntfs), uses genfs_contexts