tbl
2006-12-06, 06:06 AM CST
hi all :)
Got a problem with a new usb flash disk i-gear 512mo.
Nothing recognize when running fdisk -l.
what may i try to use my new usb key ?
THX !
My fc5 cant automount it. when i run dmesg i 've got the following :
usb 5-4: new high speed USB device using ehci_hcd and address 52
usb 5-4: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 52
usb-storage: waiting for device to settle before scanning
Vendor: CBM Model: Flash Disk Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdc: 996095 512-byte hdwr sectors (510 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 996095 512-byte hdwr sectors (510 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 9:0:0:0: Attached scsi removable disk sdc
sd 9:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
hub 5-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
usb 5-4: reset high speed USB device using ehci_hcd and address 52
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
hub 5-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
usb 5-4: reset high speed USB device using ehci_hcd and address 52
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
[root@ws043 ~]#
Got a problem with a new usb flash disk i-gear 512mo.
Nothing recognize when running fdisk -l.
what may i try to use my new usb key ?
THX !
My fc5 cant automount it. when i run dmesg i 've got the following :
usb 5-4: new high speed USB device using ehci_hcd and address 52
usb 5-4: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 52
usb-storage: waiting for device to settle before scanning
Vendor: CBM Model: Flash Disk Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdc: 996095 512-byte hdwr sectors (510 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 996095 512-byte hdwr sectors (510 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sdc: sdc1
sd 9:0:0:0: Attached scsi removable disk sdc
sd 9:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
hub 5-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
usb 5-4: reset high speed USB device using ehci_hcd and address 52
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
hub 5-0:1.0: Cannot enable port 4. Maybe the USB cable is bad?
usb 5-4: reset high speed USB device using ehci_hcd and address 52
ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 5-0:1.0: hub_port_status failed (err = -32)
[root@ws043 ~]#