USB ports problems in FC6

[garnettk]

Hi all. I installed FC6 5.91 (Test2) just now and found my usb devices cannot work properly.
They work fine in WINXP and FC5. I cannot use my mouse now(need to use touchpad instead). Can anyone help me? thx



here is my xorg.conf:


# XFree86 4 configuration created by pyxf86config

Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Synaptics" "CorePointer"
EndSection

Section "Module"
Load "synaptics"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "InputDevice"
Identifier "Synaptics"
Driver "synaptics"
Option "Device" "/dev/input/mice"
Option "Protocol" "auto-dev"
Option "Emulate3Buttons" "yes"
Option "LeftEdge" "120"
Option "RightEdge" "830"
Option "TopEdge" "120"
Option "BottomEdge" "650"
Option "FingerLow" "14"
Option "FingerHigh" "15"
Option "MaxTapMove" "110"
Option "VertScrollDelta" "20"
Option "HorizScrollDelta" "20"
Option "MinSpeed" "0.3"
Option "MaxSpeed" "0.75"
EndSection

Section "Device"
Identifier "Videocard0"
Driver "nv"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
DefaultDepth 16
EndSection








and result of lspci:


00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, fast devsel, latency 0
Memory at b0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 2.0

00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: a0000000-afffffff

00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at 1200 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1600 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1700 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 7
Memory at f4000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: d0000000-dfffffff
Prefetchable memory behind bridge: 90000000-9fffffff

00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 1100 [size=16]
Memory at 50000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: medium devsel, IRQ 11
I/O ports at 1400 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
Subsystem: COMPAL Electronics Inc Unknown device 0017
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at e000 [size=256]
I/O ports at e100 [size=64]
Memory at f0000400 (32-bit, non-prefetchable) [size=512]
Memory at f0000600 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at e200 [size=256]
I/O ports at e300 [size=128]
Capabilities: [50] Power Management version 2

01:00.0 VGA compatible controller: nVidia Corporation NV34M [GeForce FX Go5200] (rev a1) (prog-if 00 [VGA])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Memory at a0000000 (32-bit, prefetchable) [size=256M]
[virtual] Expansion ROM at e1000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0

02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 128, IRQ 11
Memory at d0001800 (32-bit, non-prefetchable) [size=2K]
Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2

02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 128, IRQ 11
I/O ports at a000 [size=256]
Memory at d0001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
Subsystem: Intel Corporation Unknown device 2702
Flags: medium devsel, IRQ 11
Memory at d0000000 (32-bit, non-prefetchable) [disabled] [size=4K]
Capabilities: [dc] Power Management version 2

02:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
Subsystem: COMPAL Electronics Inc Unknown device 0012
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 90000000-91fff000 (prefetchable)
Memory window 1: d2000000-d3fff000
I/O window 0: 0000a400-0000a4ff
I/O window 1: 0000a800-0000a8ff
16-bit legacy interface ports at 0001

[RahulSundaram]

Hi all. I installed FC6 5.91 (Test2) just now and found my usb devices cannot work properly.
They work fine in WINXP and FC5. I cannot use my mouse now(need to use touchpad instead). Can anyone help me? thx


Run yum update and boot into the latest kernel to check if the problem persists, if it does, fille a bug report in http://bugzilla.redhat.com with the kernel version and other information.

Test release discussions are better done in fedora-test list

https://www.redhat.com/archives/fedora-test-list/

[garnettk]

Sorry... when I run yum update...
the following error occured

[root@localhost ~]# yum update
Setting up Update Process
Setting up repositories
Reading repository metadata in from local files
No Packages marked for Update/Obsoletion



I am using 2.6.17-1.2517.fc6 kernel. thank you

[RahulSundaram]

Sorry... when I run yum update...
the following error occured

[root@localhost ~]# yum update
Setting up Update Process
Setting up repositories
Reading repository metadata in from local files
No Packages marked for Update/Obsoletion



I am using 2.6.17-1.2517.fc6 kernel. thank you

There is no error here. Yum just informs you that no updates are available. So file a bug report in http://bugzilla.redhat.com

[garnettk]

As far as I know, the latest kernel is not the default one provided by FC6 test2.
I wanna update it by yum. It's frustrating that I cannot use yum to update and install things :(

p.s. RPM is another route I know. However, I am still a newbie:P

[Seve]

As far as I know, the latest kernel is not the default one provided by FC6 test2.
I wanna update it by yum. It's frustrating that I cannot use yum to update and install things :(

p.s. RPM is another route I know. However, I am still a newbie:P
Hello:
Yum should work fine?
When you open a terminal and log in as root using
su -
password
type
yum clean all
then type
yum clean dbcache
then type
yum clean metadata

then do a
yum update

Sometimes yum gets (in lay terms) a bit confused.
Seve

[RahulSundaram]

As far as I know, the latest kernel is not the default one provided by FC6 test2.
I wanna update it by yum. It's frustrating that I cannot use yum to update and install things :(

p.s. RPM is another route I know. However, I am still a newbie:P


The development tree kernel which you will get when you run yum update on a test release is the very latest git snapshot available. It is actually 2.6.18 tree. You can look at the changelog to know this.

[garnettk]

when I run yum upgrade kernel
yum replies that no update is found.
I found that FC6 Test2 is a bit uncompleted